smda50 series 50w desktop power supply for medical equipment C wide input voltage 90 to 264 vac, 47 to 63hz C iec - 320 - c14 input inlet C output voltage available from 2vdc thru 50vdc C single to triple output C input surge current, over voltage, output voltage, and over load protection. C splash proof C class i insulation 3 year warranty approvals: single output model number output voltage max. output current total regulation max. output power smda50 - s00 2 ~ 3 vdc 12.0 ~ 10.0 a 7% 30w smda50 - s01 3 ~ 5 vdc 10.0 ~ 8.00 a 5% 40w smda50 - s02 5 ~ 6 vdc 8.00 ~ 6.66 a 5% 40w smda50 - s03 6 ~ 8 vdc 7.00 ~ 5.25 a 5% 42w smda50 - s04 8 ~ 11 vdc 5.63 ~ 4.00 a 4% 45w smda50 - s05 11 ~ 13 vdc 4.00 ~ 3.46 a 3% 45w smda50 - s06 13 ~ 16 vdc 3.46 ~ 2.81 a 3% 45w smda50 - s07 16 ~ 21 vdc 3.12 ~ 2.38 a 3% 50w smda50 - s08 21 ~ 27 vdc 2.30 ~ 1.85 a 2% 50w smda50 - s09 27 ~ 33 vdc 1.85 ~ 1.51 a 2% 50w smda50 - s10 33 ~ 40 vdc 1.51 ~ 1.25 a 2% 50w smda50 - s11 40 ~ 50 vdc 1.25 ~ 1.00 a 2% 50w multi output part number output 1 output 2 output 3 max. output power vonom iomin iomax regmax vonom iomin iomax regmax vonom iomin iomax regmax smda50 - d00 +3.3v 0.5a 5a 7% +12v 0.2a 2a 5% 40w smda50 - d01 +5v 0.5a 5a 5% +12v 0.2a 2a 5% 42w smda50 - d02 +5v 0.5a 5a 5% +15v 0.15a 1.5a 5% 42w smda50 - d03 +5v 0.5a 5a 5% +24v 0.1a 1a 5% 42w smda50 - d04 +3.3v 0.5a 5a 7% +5v 0.2a 2a 5% 26.5w smda50 - d09 +12v 0.3a 3a 5% - 12v 0a 1a 5% 42w smda50 - d10 +15v 0.2a 2a 5% - 15v 0.1a 1a 5% 42w smda50 - d15 +5v 0.5a 5a 5% - 24v 0.1a 1a 5% 42w smda50 - d16 +5.1v 0.5a 5a 5% +7.2v 0.3a 2.6a 5% 42w smda50 - d17 +10.5v 0.2a 2a 5% - 10.5v 0a 2a 5% 42w smda50 - d18 +5v 0.5a 5a 5% - 5v 0a 2a 5% 35w smda50 - t00 +3.3v 0.5a 5a 7% +12v 0.4a 2a 5% - 12v 0.1a 0.8a 5% 42w smda50 - t01 +5v 0.5a 5a 5% +12v 0.2a 2a 5% - 5v 0a 0.8a 5% 42w smda50 - t02 +5v 0.5a 5a 5% +12v 0.2a 2a 5% - 12v 0.1a 0.8a 5% 42w smda50 - t03 +5v 0.5a 5a 5% +15v 0.4a 2a 6% - 15v 0.1a 0.8a 5% 42w smda50 - t04 +5v 0.5a 5a 5% +24v 0.2a 1a 5% - 24v 0a 0.5a 5% 42w smda50 - t05 +5v 0.5a 5a 5% +24v 0.1a 1a 5% - 12v 0a 0.8a 5% 42w smda50 - t06 +3.3v 0.5a 5a 7% +12v 0.4a 2a 5% - 5v 0.1a 0.8a 5% 42w s00, d04, d18 is not approved by pse
electrical characteristics parameter test conditions min. typ. max. unit input voltage operating voltage 90 264 vac input frequency 47 63 hz output power range vin= 90 to 264 vac 0 50 w input current (low line) io=full load, vin=115 vac 1.35 a input current (high line) io=full load, vin= 230 vac 0. 8 a low line inrush current io=full load, 25c, cool start, vin=115vac 12 15 a high line inrush current io=full load, 25c, cool start, vin=230 vac 26 30 a efficiency io=full load, vin=230vac 75 83 88 % line regulation io=full load 0.5 1 % load regulation vin=230vac 3 7 % over voltage protection 112 132 % over current protection 110 150 % transient response io=full load to half load, vin=100vac 4 ms hold - up time io=full load, vin=110vac 16 ms start up time io=full load, vin=100vac 0.3 1.5 2 s * ripple & noise (peak to peak) full load, vin=90vac 0 .5 1 % safety ground leakage current io= full load, vin=240vac 0.1 ma temperature coefficient all output - 0.04 0.04 %/c * the ripple & noise which is under 3.3vdc at 2% max conditions parameter test conditions min. typ. max. unit operating temperature 0 50 70 c storage temperature - 40 85 c relative humidity 5 95 % operating temperature at 25 c , calculated per mil - hdbk - 217f 0.1 m hrs de - rate linearly from 100% load at 50c to 50% load at 70c approvals and compliance parameter test conditions min. unit dielectric withstanding voltage for primary to secondary primary to secondary 56 56 vdc dielectric withstanding voltage for primary to ground primary to ground 28 28 vdc isolation resistance test voltage = 5 00vdc 50 m emi requirements for cispr - 11 vin=220vac b class emi requirements for fcc part - 18 vin=110vac b class mechanical and pin out 1. dimensions are shown in inches or mm. 2. weight: 510 - 560gs approx. 3. optional output connector
|
